Best Way to Lift a Car at Home

Best Way to Lift a Car at Home Without Being Crushed

If you own a car, knowing how to lift it for repairs is an essential life skill. 

You never know when you may need to raise a specific portion of your car to get certain things fixed. It’s super easy if you know how to do it. But if you don’t properly understand the process, you may (and most importantly will) get hurt. 

Such accidents can damage your car too. Fortunately, learning the skill of lifting a car doesn’t require repeated practice. You just have to follow specific tactics. Keep reading, and you will learn everything you need to know.  

Lifting A Car with Car Jack: Finest Method I Found

You’ve probably expected to find something like this. A car jack is, in fact, the ideal, if not the best, tool for raising a car from the ground. The process is very simple; the best thing about it is you can do it all yourself. 

At first, you will need a car jack. You can buy one from Amazon for around a hundred bucks. Jack stand is also an important tool. It helps to adjust the height of the car. 

Finally, you are going to need some fine-quality wheel chocks. It’s mandatory to make sure your car doesn’t move during the repair process. Wheel chocks will ensure that. Only two of these are sufficient. 

Best Way to Lift a Car at Home

Now, once you have gathered all the tools, you can get right into the process. Here’s a step-by-step guide: 

Step 1: Prepare the vehicle for the lift

Before getting into the main task, you must ensure your car is positioned correctly. 

Firstly, choose a flat surface to position your vehicle and put the car chocks on the wheels you won’t lift. Make sure to put the car in “Parking Mode” unless you want to visit the emergency room. 

Finally, and most importantly, see if the car engine is on or if any doors are unlocked. Close all of them to avoid accidents.

Step 2: Position the car jack 

You are aware that the car jack goes right under the frame. However, are there specific points to position the jack? Yes, that’s right. Check your car’s user manual to locate the jack points. 

Next, choose the portion you need to lift. Then, place the jack in the jack points right underneath the frame. You must raise the jack a bit to connect the tool to its designated spot. 

Double-check to make sure that the tool is tightly fit in the position. 

Step 3: Lift the car up

Now comes the main segment. Slowly pump the handle of the car jack to elevate the car from beneath. Being steady and slow is the key here. 

At first, you won’t have to put much pressure. But as the car gets higher, it will be harder to pump the handle. Nevertheless, you won’t have to work that hard. Stop pumping as the car is around 6 feet up from the ground. 

If 6 feet is too low, let me tell you something important. Don’t follow this article if you intend to work underneath the car. 

You should never crawl under a vehicle that is supported by jacks. There’s a massive chance of major, fatal injuries. In case you need to get beneath, there are different lifting tools.  

However, a car jack works perfectly for minor tasks like changing the wheel. 

Step 4: Secure the car in the current position

Don’t just get right into the repair job as soon as the car is lifted. You must secure the car in the hovered position to work uninterrupted. 

For this, you are going to need jack stands.

Place the jack stands under the frames or the engine cradle. Adjust the jack stand height to the point where it meets the lifted car. Once the car is securely placed, slowly lower the car jack and move it out of the way. This will give you a clearer workspace.

Finally, after removing the car jack, give the car a little shake to see if it moves or wiggles. If it doesn’t, then you have done it!

What if You Don’t Have a Car Jack?

No car jack near your reach, but still need to get the car up a bit? 

Yes, it’s possible. Unfortunately, other arrangements facilitate only limited usage. For example, if you use an oil change ramp, you can technically lift the car up from the ground. 

But, as the wheels will be directly on the ramp, you can’t do anything to it. Nor can you do anything under the car. Because the car can slide off the ramp any minute. Due to a lack of space, you can’t even chock the wheels on the ramp. 

However, there is a unique and rather fun tactic that gets the job done. Before getting to the process, you should know that this is something you should do as a desperate measure. 

Try it if you don’t have any other option. 

The trick of lifting a car without a lifting tool requires bricks or wood, or anything like a sturdy block. Firstly, park your car on the soft ground. 

Now, place the block under the frames near the wheels you want to lift. 

Then, just dig the ground under the wheel you want to lift. The leverage provided by the block will keep the car hovered while the dirt underneath the wheel is removed. After removing a bit of dirt, the wheel should be lifted.

Digging the right amount of dirt is the most challenging part of this task. But if you think about it, it’s a very practical solution. So do give it a try in case of an emergency. 

Questions I Frequently Get About Lifting Cars at Home

I get tons of questions regarding raising vehicles and other relevant tasks. In this section, I will try to answer those queries. Give it a read if possible. It can help you.

Yes, there are a few alternatives to a car jack. 

For example, ramps are a popular method to raise the car. But it’s not an effective technique because the wheel is in direct contact with the surface of the ramp. 

As a result, there’s no way to work on the wheel. However, a ramp can be a good option if you intend to do other tasks.

Among many options, bottle jacks (aka classic floor jacks) work the best. Its super-low height and long handle work best to lift any car with the least amount of toil effortlessly. 

Unless you are a winner or a runner-up of World’s Strongest Man, chances are you won’t be able to lift a car. 

It’s recommended that you don’t try performing such experiences because it can break your back. Instead, use a tool or follow the other tactics mentioned in this article.

Summing It All Up!

A portable car jack is an ideal tool to lift any vehicle at home. It doesn’t cost a lot, nor is it difficult to use. 

You can put it in the corner of your garage, and you won’t even notice it unless you need to use it. If you have read this article thoroughly, you now have all the ideas you need to lift a car at home without anyone’s help. 

Not only this, but you’ve also learned how to raise your vehicle even if you don’t have the right tools. All this knowledge will help you get out of your situation with ease. Just stay a bit attentive and focused.

Eddie Burton - Senior Author
Senior Author: Eddie Burton

Eddie Burton is a passionate car enthusiast and a seasoned mechanic with over 15 years of experience in the automotive industry. He has worked with a variety of vehicles, from classic muscle cars to modern luxury cars, and has extensive knowledge of all types of auto parts and accessories.

Eddie’s love for cars began at a young age when he would spend hours tinkering with his first car, a 1967 Mustang. Since then, he has pursued his passion for cars by working in various garages and workshops, honing his skills and expertise in everything related to automobiles.

As a contributor to our website, Eddie shares his in-depth knowledge and experience with our readers, providing valuable tips and advice on auto parts, repairs, and maintenance. He’s committed to helping car owners get the most out of their vehicles by providing honest and practical reviews of auto parts, accessories, and tools.

With Eddie’s vast experience and expertise, you can trust his recommendations and insights on everything related to cars. Whether you’re a seasoned car owner or a newbie in the world of automobiles, Eddie’s articles and reviews will help you make informed decisions and keep your vehicle running smoothly for years to come.

Similar Posts

Leave a Reply

Your email address will not be published. Required fields are marked *